Teejet Legacy 6000 CAN Guide Bedienungsanleitung PDF herunterladen (Seite 25)

Fieldware for The Legacy 6000

Software Version 2.11

Chapter 1 - System Introduction 1-15

Typical Legacy 6000 Configurations

Single Channel Granular Spreader

This is a typical single product granular configuration with spreader control.

Figure 1-11: Single Channel Granular Spreader Configuration

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 193 194

USER GUIDE 1
Copyrights 2
Trademarks 2
Limitation of Liability 2
Table of Contents 3
Fieldware for The Legacy 6000 10
System Introduction 12
CAN Bus Versatility and Value 13
The Legacy 6000 Console 15
Power Speed Module 16
Switch Sense Module 17
Switch Function Module 18
Product Control Module 19
Swath XL Lightbar 20
CAN Bus Cable Specifications 21
CAN Modules (PCM, SSM, PSM) 21
Cable Harnesses 22
PCM Cable Options 23
Table 1-1: PCM Cable Options 23
Chapter 2 - Getting Started 31
Software Overview 32
Standard Pages 34
Setup Menu Page 35
Setup Wizard 35
Setup Sub-Groups 35
Exiting a Setup Menu Page 35
Data Entry Page 36
System Setup 37
Console Setup 38
Lightbar Setup 39
GPS Receiver Setup 40
Implement Setup 41
Entering the Implement Width 42
Number of Swaths Page 43
Entering the Section Width 44
The Offset Distance Y 45
Setting the PCM Assignment 47
Completing Implement Setup 48
PCM Serial Number 49
PCM Number 49
PCM Name 49
Favorites Description 51
Setting the Application Type 52
Application 53
Settings 53
Setting the Drive Type 54
Servo Settings Description 55
PWM Settings Description 55
Setting the Units 57
Selecting the Primary Sensor 58
Sensor Settings Definition 59
Selecting a Monitor 64
Monitor Settings Description 65
Finishing the PCM Setup 67
Chapter 3 - Real-time Setup 71
Operation Overview 72
Step Description 73
Figure 3-3: The Job Name Page 75
No PCMCIA Card Setup 76
ARM Launcher 77
Performing a Calibration 78
Distance/Speed Calibration 79
Pressure Calibration 89
NH3 In-Field Calibration 91
Injection Static Calibration 93
Prime Injection System 95
2. Setup System for Priming 96
3. Start Prime 96
2. Start Reverse Prime 98
Job Report Setup 99
Item Description 100
ARM Setup 101
Setup Item Description 102
Software Version 2.11 103
Folder Button 104
Product Setup 105
The Select PCM Page 107
Select the Product Name 108
Variable Rate Application 109
Multiproduct Variable Rate 110
Chapter Notes 113
Fieldware for the Legacy 6000 114
Product Application 116
Information Pages 117
Manual Control 118
Test Speed 119
Reset Initial Quantity 119
Soft-key Description 120
The Map Page 121
System Message 125
Warning Message 125
Error Message 126
Real-time Guidance Operation 127
Mark Point A 128
Mark Point B 128
The Headland Guidance Pattern 129
Headland Pattern Example 130
Step 4: Ignore Headland Data 135
The Circle Pivot Pattern 137
Circle Pivot Example 138
Marking Point A 138
Marking Point B 138
Applied Area Detection 142
Mapping a Field Boundary 144
Mapping Points and Hazards 146
Marking a Hazard 147
Object Name File 147
Exiting Real-Time Operation 148
Lightbar Index 149
Lightbar State Description 150
Chapter 5 - System Tools 155
System Tools 156
Device Manager 157
Figure 5-4: 158
Button Description 158
Figure 5-6: 160
Required Items: 161
Card Manager 163
5-12 Chapter 5 - System Tools 166
5Chapter Notes 166
Chapter 6 - Running Mapper 167
Mapper Introduction 168
Starting a Job 169
Figure 6-3: The Job Name Page 170
Soft-key Step Description 171
Table 6-1: Mapper Setup 171
Figure 6-4: Mapper Setup 172
Mapper Setup 172
Description 172
Parameter Description 173
Enter Road Marker Name 174
Creating Object Name 175
Real-time pages 176
Mapper Tools 180
Object Description 181
Figure 6-13: The Options Menu 182
Option Description 182
LIQFLOW-A GRANSERVO-A 185
GRANSERVO-B GRANPWM-A 186
GRANDC-A SPINMOTOR-A 187
Using the Calibration Table 191
Appendix C - NH3 Application 193

Kommentare zu diesen Handbüchern

Keine Kommentare

Teejet Legacy 6000 CAN Guide Bedienungsanleitung Seite 25

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Computers Teejet Legacy 6000 CAN Guide