Teejet Matrix 840G User Manual Bedienungsanleitung Seite 27
- Seite / 58
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
www.teejet.com
40
●
98-05141 R2
41
●
VEHICLE SETUP
Vehicle Setup is used to confi gure
Vehicle Type, Antenna Height, Direction
to Boom, and Boom Offset Distance.
1. Select UNIT SETUP
from Home Menu .
2. Press VEHICLE SETUP TAB .
3. Select from:
►Vehicle Type – selects the type of
vehicle that most closely represents your vehicle
►Antenna Height – sets the height of the
antenna from the ground
►Direction to Boom – sets whether the
boom is located behind or in front of the GPS
antenna
►Boom Offset Distance – defi nes the
distance from the GPS antenna to the boom
OR
Press PAGE RIGHT ARROW to cycle through
all settings.
NOTE: Options labels are current settings. While in
a setting screen, press icon to view available
factory settings and setting ranges.
Figure 2-47: Vehicle Setup
Vehicle Type
Vehicle Type selects the type of vehicle steering that
most closely represents your vehicle.
1. Press VEHICLE TYPE ICON
2. Press UP/DOWN ARROW ICONS to
change between:
►Front Wheel Steer (also used for
Combines)
►Articulated
►Tracked
3. Press
►PAGE RIGHT ARROW to proceed to
Antenna Height.
►VEHICLE SETUP TAB to return to main
Vehicle Setup screen.
NOTE: This setting is required for FieldPilot and
Tilt Sensor Operation, as well as proper
BoomPilot operation.
Figure 2-48: Vehicle Type
Single Boom Setup
Single Boom Setup is available when a SmartCable
or Section Driver Module (SDM) is not present.
Confi gurations for Overlap, Delay On, Delay Off,
Number of Boom Sections will not be available, and
only one boom section width can be entered.
Boom Section Width
Boom Section Width establishes the width of entire
swath. Range is 34.0 - 1968.5 inches / 0.9 - 50.0
meters.
1. Select UNIT SETUP from Home Menu .
2. Press BOOMPILOT/SINGLE BOOM SETUP
TAB .
3. Press
►BOOM SECTION WIDTH ICON .
►PAGE RIGHT ARROW .
4. Use the entry screen to establish swath width.
5. Press
►CHECKERED FLAG to complete Boom
Section Setup.
►BOOMPILOT/SINGLE BOOM SETUP TAB
to return to main Boom Section Setup screen.
NOTE: Options label is current setting. While in a
setting screen, press icon to view available
factory settings and setting ranges.
NOTE: This setting is required for FieldPilot and Tilt
Sensor Operation.
Figure 2-45: Single Boom Section Width (No SDM)
Figure 2-46: Single Boom Section Width Entry
- USER MANUAL 1
- CHAPTER 1– PRODUCT OVERVIEW 7
- SYSTEM FEATURES 7
- Matrix 840G Console 8
- SYSTEM COMPONENTS 8
- Matrix 570G Console 8
- RealView Camera 9
- Video Selector Modules 9
- GPS Antennas 9
- FieldPilot 9
- Steering Control Module 9
- 98-05141 R2 10
- CONFIGURATIONS 11
- Engage/Disengage 12
- POWER ON/OFF 13
- Start Up Sequence 14
- GENERAL OPERATION 14
- INFORMATION 14
- Page Layout and Navigation 15
- CHAPTER 2 – UNIT SETUP 16
- Lightbar 17
- Home Menu 17
- SYSTEM SETUP 17
- LED Brightness 18
- Display Mode 18
- Time Zone 19
- Language 19
- Requirements 20
- GPS Status 20
- GPS Type 20
- GPS Port 20
- LCD Brightness 21
- GGA Requirements 21
- Software Version 1.03 22
- Software Version 1.00 to 1.02 22
- Next Power Cycle 22
- Save About Information 23
- Screenshot 23
- Enable/Disable 23
- Capture an Image 23
- About/Save 23
- Four Channel VSM 24
- Eight Channel VSM 24
- BOOMPILOT/SINGLE 25
- BOOM SETUP 25
- BoomPilot Setup 25
- Number of Boom Sections 26
- Boom Section Width 26
- Delay On 26
- Delay Off 26
- VEHICLE SETUP 27
- Single Boom Setup 27
- TILT GYRO MODULE 28
- Valve Setup 30
- FIELDPILOT SETUP 30
- Autosteer 30
- Cycle Right 31
- Maximum Duty Cycle 31
- Minimum Duty Cycle 31
- Cycle Left 31
- Con gure FieldPilot 32
- Valve Test 32
- Deadband 33
- Coarse Steering Adjustment 33
- Fine Steering Adjustment 33
- Lookahead 34
- CHAPTER 3 – GUIDANCE 35
- GUIDANCE OPERATION 35
- Straight A-B Guidance 35
- GUIDANCE BAR & STATUS BAR 36
- Guidance Bar 36
- Curved A-B Guidance 36
- Circle Pivot Guidance 36
- Last Pass Guidance 36
- VEHICLE VIEW 37
- Status Bar 37
- Vehicle View 38
- Guidance Mode Select 38
- Zoom In/Out & 41
- Perspective 41
- BoomPilot 41
- Field View 42
- Field Boundary 42
- FIELD VIEW 42
- Return to Point 43
- Zoom In/Out 44
- World View 44
- Pan Mode 44
- REALVIEW GUIDANCE 44
- RealView Guidance 45
- Full Screen 45
- Guidance Over Video 45
- Steering Angle Indicator 46
- Single Camera Selection 46
- Split Camera View 47
- Guideline Adjustment 48
- CHAPTER 4 – MONITORING 49
- JOB VIEW 49
- Job Information 49
- Save Information 50
- BOOM MONITORING 51
- Boom Monitor 51
- APPENDIX A ICON REFERENCE 53
- Menu Options 53
- CHAPTER 5 – APPENDIX 53
- Unit Setup 54
- Job View 55
- Guidance Screens 55
- APPENDIX B TIME ZONES 56
- APPENDIX D UNIT 57
- SPECIFICATIONS 57
- APPENDIX C FACTORY 57
- SETTINGS & RANGES 57
Verwandte Produkte und Handbücher für Computers Teejet Matrix 840G User Manual
(2 Seiten)
(2 Seiten)
(2 Seiten)
(2 Seiten)
(2 Seiten)
Computers Teejet Matrix 430 Bedienungsanleitung
(12 Seiten)
(12 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.115 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern