Teejet Matrix Pro 840G User Manual Bedienungsanleitung Seite 28
- Seite / 127
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
21
98-05238 R1 EN-US
HOME OVERVIEWSETUP POWERAPPENDIX FULL SCREEN INTRODUCTIONGUIDANCE
Vehicle Setup
1. Press CONFIGURATION side tab .
2. Press Vehicle .
3. Select from:
►Vehicle Type – selects the type of vehicle that most closely
represents your vehicle
►Antenna Height – sets the height of the antenna from the
ground
►Direction to Boom – sets whether the boom is located
behind or in front of the GPS antenna
►Distance to Boom
– denes the distance from the GPS
antenna to the boom
4. Press RETURN arrow
or CONFIGURATION side tab to
return to the main Conguration screen.
Figure 3-16: Vehicle Setup Options
Conguration
Vehicle
Implement
AutoSteer
Tilt
Lightbar
GPS
Video
Cong-> Vehicle
Vehicle Type
Ant Height
Dir to Boom
Dist to Boom
12.50 ft
0.00 ft
Front Wheel
Backward
AutoSteer Setup
When a Steering Control Module (SCM) is present, Assisted/Auto
Steering options will be available. For detailed setup instructions,
refer to your specic assisted/auto steering installation manual.
NOTE: An update of your SCM software will also be required when
updating an existing Matrix console to Matrix Pro.
1. Press CONFIGURATION side tab .
2. Press
AutoSteer .
3. Select:
►On – enabled
►Off – disabled
4. Select from:
►Valve Setup – used to congure Valve Type, Valve Frequency,
Minimum Duty Cycle Left, Minimum Duty Cycle Right and
Maximum Duty Cycle
►Steering Settings – used to establish Coarse Adjustment, Fine
Adjustment, Deadband and Lookahead
►Valve Test – used to verify if steering is directed correctly
►Valve Diagnostics – used to test the valves to see if they are
connected properly
►Options: Steering Wheel Sensor – used to select whether the
steering disengage sensor is magnetic or pressure based
►Angle Sensor – used to establish the Steering Angle Sensor
(SAS) as the primary feedback sensor for auto steering,
calibrate the SAS and set an offset adjustment.
5. Press RETURN arrow
or CONFIGURATION side tab to
return to the main Conguration screen.
Figure 3-17: AutoSteer
Conguration
Vehicle
Implement
AutoSteer
Tilt
Lightbar
GPS
Video
Cong-> AutoSteer
Enabled
Valve Setup
Steering Settings
Valve Test
Valve Diagnostics
Angle SensorOptions
On
- UsER MANUAL 1
- Table of Contents 2
- CHAPTER 6 SYSTEM SETUP 32 3
- CHAPTER 7 GUIDANCE 78 5
- CHAPTER 1 SYSTEM OVERVIEW 8
- SYSTEM COMPONENTS 9
- Matrix Pro 570G Console 9
- Additional Information 9
- Matrix Pro 840G Console 10
- RealView Camera 10
- Optional Accessories 11
- 98-05238 R1 EN-US 12
- CONFIGURATIONS 13
- 45-10103 15
- DC: xx/xx 15
- Speed Cable 17
- CHAPTER 2 POWER 18
- Setup Screens 20
- Setup Option Information 21
- Drop Down Menu Selections 21
- Dist to Boom (ft) 22
- Conguration 23
- < 0.0 > 24
- Simple Mode 29
- Advanced Mode 29
- SIMPLE MODE 30
- 8.9 < 32
- ADVANCED MODE 33
- 12/14/10 3:52 AM 36
- Continue 36
- CHAPTER 6 SYSTEM SETUP 39
- Ant Height (ft) 41
- Antenna Height (ft) 43
- Guidance Width (ft) 46
- Section 1 Width (in) 46
- Delay On Time (s) 47
- Delay O Time (s) 47
- Valve Setup 49
- Valve Type 49
- Valve Frequency (Hz) 50
- Test Right 51
- Steering Settings 53
- Coarse Steering Adjustment 53
- Fine Steering Adjustment 53
- Deadband 54
- Lookahead 54
- Valve Test 54
- Valve Diagnostics 55
- 1. Select Angle Sensor 57
- Enable/Disable Angle Sensor 58
- Calibrate Sensor 58
- Offset Adjustment 59
- Field Level 61
- LED Spacing (ft) 63
- GPS Status 65
- GGA Requirements 65
- Four Channel VSM 67
- Eight Channel VSM 67
- DATA MANAGEMENT 68
- Manage Data 68
- Manage Data Unavailable 69
- Duplicate Job Data 69
- Transfer 70
- Transfer Unavailable 71
- USB Storage 71
- Internal Storage 72
- Delete Job Data 72
- Reports 73
- Simple Job Mode Options 74
- Advanced Job Mode Options 74
- ESRI Data 75
- PDF Report 75
- KML Data 75
- CONSOLE 77
- Color Scheme 78
- Brightness 78
- Screenshot 78
- Capture a Screenshot 79
- Touch Screen Calibration 79
- Cultural 80
- Time Zone 81
- Calculator 83
- Units Converter 83
- Set Units 84
- Select Value 84
- 0.0 mph 0 ac 85
- Navigation Screens Icons 86
- Status/Information Screens 89
- Assisted/Auto Steering Status 90
- BoomPilot Status 90
- 0.0 mph 0.00 ac 100
- -13 7.2 mph 101
- A+ Nudge Feature 102
- > 0.0 < 103
- Enter Name 104
- Circle Pivot Guidelines 106
- Last Pass Guidelines 108
- Turn Now 109
- 12.7 > 109
- APPLICATION BOUNDARY 110
- Save Delete 111
- RETURN TO POINT 112
- Single Section 114
- ZOOM IN/OUT 114
- Vehicle View 114
- Field View 115
- PAN MODE 116
- REALVIEW SPECIFIC OPTIONS 116
- Single Camera Selection 117
- Split Camera View 118
- RealView Setup Options 118
- Guidance Over Video 119
- Guidance Unavailable 119
- Horizon Line Adjustment 119
- Steering Angle Indicator 120
- APPENDIX A TIME ZONES 121
- Atlantic 122
- Australia 122
- 0.0 ft 123
- Data Management 124
- Console Settings 125
Verwandte Produkte und Handbücher für Computers Teejet Matrix Pro 840G User Manual
(9 Seiten)
(9 Seiten)
(9 Seiten)
(9 Seiten)
(9 Seiten)
Computers Teejet Matrix 430 Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Computers Teejet UniPilot Bedienungsanleitung
(20 Seiten)
(20 Seiten)
Computers Teejet RX510 Bedienungsanleitung
(3 Seiten)
(3 Seiten)
Computers Teejet RMS Office Bedienungsanleitung
(120 Seiten)
(120 Seiten)
Computers Teejet RX370p Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Computers Teejet RX 400p Bedienungsanleitung
(151 Seiten)
(151 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern